MGB luggage rack :

Revo-Rack black $409.95 / £329.95 / 349.95€

Revo-Rack PA $489.95 / £389.95 / 419.95€

red mgb with a revo-rack pa luggage rack fitted photographed close at the rear at a car show

No metal clamps on fragile trunk lid edges and enjoyed by our customers since 2016

Revo-Rack is a unique design of MGB Luggage Rack that eliminates the risk of paint damage, caused by steel clamps or straps on the fragile boot/trunk lid edges.

We have been manufacturing the Revo-Rack since 2016 with the choice of two finishes black or PA (polished anodised) which creates a chrome like shine. We only sell direct over the web.

We designed Revo-Rack in 2015. The issue with fitting a conventional metal clamp based luggage rack to a modern convertible trunk lid is the small panel gap - there is no room for a metal clamp.

Revo-Rack attaches to your MGB using vacuum cup technology, these are not suction cups. Suction is what creates vacuum. Vacuum is the total absence of air whereas suction is the process done to achieve a vacuum. The grey buttons on the side of the cups pump out the air creating a huge, securing force.

Revo-Rack attaches with huge force using soft rubber vacuum cups : no metal clamps on fragile trunk lid edges

In 2015 Revo-Rack was independently certified by TUV Italy part of the global TUV testing and certification business. It went through speed, braking and force tests, to ISO 11154:2006 Revo-Rack passed all these tests and is certified to carry 20kg/45lbs. Since 2016 we have sold over 10,000 Revo-Racks and never had a failure.

red mgb in a grass car park with revo-rack black luggage rack fited

TUV tested at 120mph with 45lb load

Why a Revo Rack MGB Trunk Luggage Rack ?

No metal clamps to chip paint
No awkward bolts
No drilling
Shipped to the USA in 2-4 days with DHL
As the Revo-Rack is less than $800 there are no import duties & no state taxes
In manufacture since 2016 tried tested and used by thousand's worldwide
No fiddly clamps on the fragile trunk lid edges
Revo-Racks load carrying capacity has been rated at 20kg / 45Ibs
Fitted and removed in under a minute ( see video below )
Not immediately obvious how to release the rack from the boot/trunk lid - Impossible to pull off, therefore theft is difficult.
Revo-Rack is designed for a days travel then remove it from the car, and refit on multi day trips ( it takes 60 seconds )
Supplied with two luggage straps and a cotton storage bag
Tested to ISO : 11154 PAS 2006

The Rack Frame :

This MGB luggage rack is manufactured from 1" 6063-T5 tubing this is an aluminium and magnesium alloy ( it will never rust ) As a result the rack frame weighs only 3.6lb perfect for todays aluminium and composite boot/trunk lids. The cross bars are machine welded in place to ensure consistency. The rack frame measures 36"x17"

The Supports :

The rack is secured to your trunk lid using three 120mm vacuum cups, rated by the manufacturer as capable of holding an 18kg/40lb load each.

Vacuum cups employ the force of atmospheric pressure to grip a surface: When a vacuum exists between the cup and the surface on which it is attached, the weight of Earth's atmosphere holds the cup in place with incredible force. Unlike suction cups that produce a vacuum as they pull away from the surface, Revo-Racks vacuum cups use a hand-actuated pump to efficiently remove air from between the rubber pad and the attaching surface thus creating a much more reliable hold. Because the full face of the pad is brought into contact with the boot/trunk lid, distortion is reduced, allowing the cup to be used with very little risk of damage.

The Revo-Racks vacuum cup's pump feature a plunger with a red line, which serves as a vacuum indicator. This safety device is still acknowledged as one of the most reliable warning systems available. A few strokes of the plunger evacuate the vacuum pad, causing it to seal securely to the attaching surface. When the cup is attached completely, the plunger stops moving and the red line is hidden within the pump. A visible red line indicates if air has leaked back into the pad, making vacuum insufficient to use the cup. However, if the red line becomes visible while the cup is in use, a check valve allows the user to re pump the cup without losing the remaining vacuum.

Lifting on the release tab near the edge of the pad allows air to refill the evacuated space, so that the vacuum cup detaches completely. The racks sits 3" off the trunk lid.